Install alignment plate as follows: DISCONNECT TOOL FROM POWER SOURCE. Index marks are provided for 11/2' wide, and 2' wide material. The alignment plate provides added support for narrow material, and has index marks to aid in centering the cut in the narrow material. 11.ĪLIGNMENT PLATE (For Narrow Stock) When joining narrow material, it will be necessary to install the alignment plate (A) Fig. Slowly release pressure on plunge mechanism. 13, fully retract the plunge mechanism, and reposition the safety lever as shown in Fig. Rotate the “quick set” depth adjusting turret (A) Fig. Continue to hold spindle lock button while using the hex wrench (furnished with tool), to tighten blade retaining bolt securely, (by rotating clockwise). If “fine tuning” of the stop position is required: use a 5 64' hex wrench (not furnished), to rotate set-screw (F) Fig. 9 FINE ADJUSTMENT (90° Position) The adjustable 90° stop is factory adjusted for 90° and should not require additional adjustment. 7 90 degrees D 135 degrees C C A D A E E Fig. 4 & 5) 1.Ħ0 degrees 0 degrees C F A B A B E E Fig.

Does not have to be removed to make “flush” cuts.

Tilts 0° through 135°, with an adjustable stop at 90°.

Provides micro height adjustment, distance scale includes indexes to top of cut, to center of cut, and to bottom of cut.

ADJUSTABLE FENCE Model 557 is equipped with an integral, adjustable fence which: While holding adjustment knob in desired position: tighten lock-nut firmly. To set depth of cut: rotate depth adjusting turret until desired size marking on turret aligns with the index mark (B) Fig. 2, provides for quick changes in depth of cut to accommodate the various sizes of available biscuits and other accessories. 1 ADJUSTING DEPTH OF GROOVE A “quick set” depth adjusting turret (A) Fig. SELECTING THE BISCUIT Biscuits are 5/32' thick.ī A Fig. ASSEMBLY NOTE: This tool is shipped completely assembled.

Adjustments are also provided which allow the tool to cut grooves for the following plate joiner accessories sold by other manufacturers: #6 biscuits, Duplex accessories, and Simplex accessories. current.įUNCTIONAL DESCRIPTION FOREWORD Model 557 is designed to cut the grooves required for Porter-Cable biscuit sizes “FF”, “0”, “10”, and “20”. Do not operate your tool on a current on which the voltage is not within correct limits. Refer to the specification plate on your tool for proper voltage and current rating. Several models, however, are designed for A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. An exposed cutter may engage the surface leading to possible loss of control and serious injury. Wait for the cutter to stop before setting the tool down. Contact with a 'live' wire will make exposed metal parts of the tool 'live' and shock the operator. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Keep your hair, clothing and gloves away from moving parts.ĪDDITIONAL SPECIFIC SAFETY RULES 1. This enables better control of the power tool in unexpected situations. Keep proper footing and balance at all times. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. GENERAL SAFETY RULES* continued d) Remove any adjusting key or wrench before turning the power tool on. Cluttered or dark areas invite accidents. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work area clean and well lit. The term 'power tool' in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. GENERAL SAFETY RULES* Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. indicates a potentially hazardous situation which, if not avoided,could result in death or serious injury. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

The symbols below are used to help you recognize this information. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS.

SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS. Record these numbers in the spaces below and retain for future reference. plate is located on the main housing of the tool. ESPAÑOL: PÁGINA 23 FRANÇAISE : PAGE 43 Instruction manual Double Insulated Plate Joiner MODEL 557 To learn more about Porter-Cable visit our website at: IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations.

Porter cable biscuit joiner